initial check-in of ASF 3.39.0

4 files changed, 451 insertions, 0 deletions

diff --git a/xmega/boards/xmega_rf212b_zigbit/board_config/conf_board.h b/xmega/boards/xmega_rf212b_zigbit/board_config/conf_board.h
new file mode 100644
index 00000000..902a7d84
--- /dev/null
+++ b/xmega/boards/xmega_rf212b_zigbit/board_config/conf_board.h
@@ -0,0 +1,55 @@
+/**
+ * \file
+ *
+ * \brief XMEGA-AT86RF212B Zigbit board configuration template
+ *
+ * Copyright (C) 2014-2015 Atmel Corporation. All rights reserved.
+ *
+ * \asf_license_start
+ *
+ * \page License
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ *
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ *
+ * 3. The name of Atmel may not be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * 4. This software may only be redistributed and used in connection with an
+ *    Atmel microcontroller product.
+ *
+ * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
+ * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
+ * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ * \asf_license_stop
+ */
+/*
+ * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
+ */
+
+#ifndef CONF_BOARD_H
+#define CONF_BOARD_H
+
+// Enabled when Zigbit Extension board is used
+//# define ZIGBIT_EXT 
+
+// Enabled when Zigbit USB-Extension board is used
+//#define ZIGBIT_USB
+
+#endif // CONF_BOARD_H
diff --git a/xmega/boards/xmega_rf212b_zigbit/init.c b/xmega/boards/xmega_rf212b_zigbit/init.c
new file mode 100644
index 00000000..48f75ec2
--- /dev/null
+++ b/xmega/boards/xmega_rf212b_zigbit/init.c
@@ -0,0 +1,98 @@
+/**
+ * \file
+ *
+ * \brief XMEGA-AT86RF212B Zigbit board init.
+ *
+ * This file contains board initialization function.
+ *
+ * Copyright (c) 2014-2015 Atmel Corporation. All rights reserved.
+ *
+ * \asf_license_start
+ *
+ * \page License
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ *
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ *
+ * 3. The name of Atmel may not be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * 4. This software may only be redistributed and used in connection with an
+ *    Atmel microcontroller product.
+ *
+ * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
+ * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
+ * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ * \asf_license_stop
+ *
+ */
+/*
+ * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
+ */
+#include <conf_board.h>
+#include <board.h>
+#include <ioport.h>
+
+
+
+void board_init(void)
+{
+
+#ifdef ZIGBIT_USB
+	ioport_configure_pin(LED0_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
+	ioport_configure_pin(LED1_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
+#endif
+
+#ifdef ZIGBIT_EXT
+	ioport_configure_pin(LED0_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
+	ioport_configure_pin(LED1_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
+	ioport_configure_pin(LED2_GPIO, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
+	ioport_configure_pin(GPIO_PUSH_BUTTON_0, IOPORT_DIR_INPUT
+			| IOPORT_LEVEL | IOPORT_PULL_UP);
+#endif
+
+
+#ifdef CONF_BOARD_ENABLE_USARTE0
+	ioport_configure_pin(IOPORT_CREATE_PIN(PORTE, 3), IOPORT_DIR_OUTPUT
+			| IOPORT_INIT_HIGH);
+	ioport_configure_pin(IOPORT_CREATE_PIN(PORTE, 2), IOPORT_DIR_INPUT);
+#endif
+
+#ifdef CONF_BOARD_ENABLE_USARTD0
+ioport_configure_pin(IOPORT_CREATE_PIN(PORTD, 3), IOPORT_DIR_OUTPUT
+| IOPORT_INIT_HIGH);
+ioport_configure_pin(IOPORT_CREATE_PIN(PORTD, 2), IOPORT_DIR_INPUT);
+#endif
+
+
+#ifdef CONF_BOARD_AT86RFX
+	ioport_configure_pin(AT86RFX_SPI_SCK, IOPORT_DIR_OUTPUT
+			| IOPORT_INIT_HIGH);
+	ioport_configure_pin(AT86RFX_SPI_MOSI, IOPORT_DIR_OUTPUT
+			| IOPORT_INIT_HIGH);
+	ioport_configure_pin(AT86RFX_SPI_MISO, IOPORT_DIR_INPUT);
+	ioport_configure_pin(AT86RFX_SPI_CS, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
+
+	/* Initialize TRX_RST and SLP_TR as GPIO. */
+	ioport_configure_pin(AT86RFX_RST_PIN, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
+	ioport_configure_pin(AT86RFX_SLP_PIN, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
+#endif
+}
+
+
diff --git a/xmega/boards/xmega_rf212b_zigbit/led.h b/xmega/boards/xmega_rf212b_zigbit/led.h
new file mode 100644
index 00000000..bb670ed0
--- /dev/null
+++ b/xmega/boards/xmega_rf212b_zigbit/led.h
@@ -0,0 +1,81 @@
+/**
+ * \file
+ *
+ * \brief XMEGA-AT86RF212B Zigbit board LEDs support package.
+ *
+ * This file contains definitions and services related to the LED features of
+ * the XMEGA-AT86RF212B Zigbit board.
+ *
+ * Copyright (c) 2014-2015 Atmel Corporation. All rights reserved.
+ *
+ * \asf_license_start
+ *
+ * \page License
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ *
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ *
+ * 3. The name of Atmel may not be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * 4. This software may only be redistributed and used in connection with an
+ *    Atmel microcontroller product.
+ *
+ * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
+ * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
+ * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ * \asf_license_stop
+ *
+ */
+/*
+ * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
+ */
+#ifndef _LED_H_
+#define _LED_H_
+
+#include "gpio.h"
+
+/**
+ * \brief Turns off the specified LEDs.
+ *
+ * \param led_gpio LED to turn off (LEDx_GPIO).
+ *
+ * \note The pins of the specified LEDs are set to GPIO output mode.
+ */
+#define LED_Off(led_gpio)     gpio_set_pin_high(led_gpio)
+
+/**
+ * \brief Turns on the specified LEDs.
+ *
+ * \param led_gpio LED to turn on (LEDx_GPIO).
+ *
+ * \note The pins of the specified LEDs are set to GPIO output mode.
+ */
+#define LED_On(led_gpio)      gpio_set_pin_low(led_gpio)
+
+/**
+ * \brief Toggles the specified LEDs.
+ *
+ * \param led_gpio LED to toggle (LEDx_GPIO).
+ *
+ * \note The pins of the specified LEDs are set to GPIO output mode.
+ */
+#define LED_Toggle(led_gpio)  gpio_toggle_pin(led_gpio)
+
+#endif /* _LED_H_ */
diff --git a/xmega/boards/xmega_rf212b_zigbit/xmega_rf212b_zigbit.h b/xmega/boards/xmega_rf212b_zigbit/xmega_rf212b_zigbit.h
new file mode 100644
index 00000000..78acba94
--- /dev/null
+++ b/xmega/boards/xmega_rf212b_zigbit/xmega_rf212b_zigbit.h
@@ -0,0 +1,217 @@
+/**
+ * \file
+ *
+ * \brief XMEGA_RF212B_ZIGBIT board header file.
+ *
+ * This file contains definitions and services related to the features of the
+ * XMEGA_RF212B_ZIGBIT board.
+ *
+ * To use this board define BOARD=XMEGA_RF212B_ZIGBIT
+ *
+ * Copyright (c) 2013-2015 Atmel Corporation. All rights reserved.
+ *
+ * \asf_license_start
+ *
+ * \page License
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ *
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ *
+ * 3. The name of Atmel may not be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * 4. This software may only be redistributed and used in connection with an
+ *    Atmel microcontroller product.
+ *
+ * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
+ * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
+ * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ * \asf_license_stop
+ *
+ */
+/*
+ * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
+ */
+#ifndef _XMEGA_RF212B_ZIGBIT_H_
+#define _XMEGA_RF212B_ZIGBIT_H_
+
+#include <compiler.h>
+# include "conf_board.h"
+
+#define MCU_SOC_NAME        "ATxmega256A3U"
+
+
+/**
+ * \defgroup xmega_rf212b_zigbit_group XMEGA-A3BU Xplained board
+ * @{
+ */
+
+/**
+ * \defgroup xmega_rf212b_zigbit_feature_group Feature definitions
+ * @{
+ */
+
+//! \name Miscellaneous data
+//@{
+//! Validate board support for the common sensor service.
+#define COMMON_SENSOR_PLATFORM
+//@}
+
+/**
+ * \name LEDs
+ *
+ * LED0 and LED1 are single yellow LEDs that are active low..
+ * LED2 and LED3 are inside one package (Led red and green close
+ * to USB connector) but can be controlled individually.
+ * LED2 has a red color and is active low. This LED can be
+ * used for general purposes.
+ * LED3 has a green color and is active high. By default this
+ * LED is on since it shall indicate that power is applied to the
+ * board. By pulling the gate of a N-FET low it is possible to
+ * turn off the LED if needed.
+ */
+//@{
+#ifdef ZIGBIT_USB
+#define BOARD_NAME          "ATZB-X-212B-USB"
+#define LED0_GPIO                       IOPORT_CREATE_PIN(PORTA, 4)
+#define LED1_GPIO                       IOPORT_CREATE_PIN(PORTA, 5)
+
+#define LED0                            LED0_GPIO
+#define LED1                            LED1_GPIO
+
+//! Number of LEDs.
+#define LED_COUNT                       2
+
+#endif
+
+#ifdef ZIGBIT_EXT
+
+#define BOARD_NAME          "ATZB-X-212B-XPRO"
+#define LED0_GPIO                       IOPORT_CREATE_PIN(PORTA, 6)
+#define LED1_GPIO                       IOPORT_CREATE_PIN(PORTA, 7)
+#define LED2_GPIO                       IOPORT_CREATE_PIN(PORTA, 5)
+
+#define LED0                            LED0_GPIO
+#define LED1                            LED1_GPIO
+#define LED2                            LED2_GPIO
+
+//! Number of LEDs.
+#define LED_COUNT                       3
+
+#define GPIO_PUSH_BUTTON_0              IOPORT_CREATE_PIN(PORTF, 2)
+
+//! \name Communication interfaces on header J1
+//@{
+#define TWID_SDA                        IOPORT_CREATE_PIN(PORTD, 0)
+#define TWID_SCL                        IOPORT_CREATE_PIN(PORTD, 1)
+#define USARTD0_RXD                     IOPORT_CREATE_PIN(PORTD, 2)
+#define USARTD0_TXD                     IOPORT_CREATE_PIN(PORTD, 3)
+#define SPID_SS                         IOPORT_CREATE_PIN(PORTD, 4)
+#define SPID_MOSI                       IOPORT_CREATE_PIN(PORTD, 5)
+#define SPID_MISO                       IOPORT_CREATE_PIN(PORTD, 6)
+#define SPID_SCK                        IOPORT_CREATE_PIN(PORTD, 7)
+//@}
+
+
+#endif
+
+//@}
+
+/*! \name Connections of the AT86RFX transceiver
+ */
+//! @{
+#define AT86RFX_SPI                  &SPIC
+#define AT86RFX_RST_PIN              IOPORT_CREATE_PIN(PORTC, 0)
+#define AT86RFX_MISC_PIN             IOPORT_CREATE_PIN(PORTC, 1)
+#define AT86RFX_IRQ_PIN              IOPORT_CREATE_PIN(PORTC, 2)
+#define AT86RFX_SLP_PIN              IOPORT_CREATE_PIN(PORTC, 3)
+#define AT86RFX_SPI_CS               IOPORT_CREATE_PIN(PORTC, 4)
+#define AT86RFX_SPI_MOSI             IOPORT_CREATE_PIN(PORTC, 5)
+#define AT86RFX_SPI_MISO             IOPORT_CREATE_PIN(PORTC, 6)
+#define AT86RFX_SPI_SCK              IOPORT_CREATE_PIN(PORTC, 7)
+
+#define AT86RFX_INTC_INIT()          ioport_configure_pin(AT86RFX_IRQ_PIN, IOPORT_DIR_INPUT); \
+									 PORTC.PIN2CTRL = PORT_ISC0_bm; \
+									 PORTC.INT0MASK = PIN2_bm; \
+									 PORTC.INTFLAGS = PORT_INT0IF_bm;
+
+#define AT86RFX_ISR()                ISR(PORTC_INT0_vect)
+
+/** Enables the transceiver main interrupt. */
+#define ENABLE_TRX_IRQ()                (PORTC.INTCTRL |= PORT_INT0LVL_gm)
+
+/** Disables the transceiver main interrupt. */
+#define DISABLE_TRX_IRQ()               (PORTC.INTCTRL &= ~PORT_INT0LVL_gm)
+
+/** Clears the transceiver main interrupt. */
+#define CLEAR_TRX_IRQ()                 (PORTC.INTFLAGS = PORT_INT0IF_bm)
+
+/*
+ * This macro saves the trx interrupt status and disables the trx interrupt.
+ */
+#define ENTER_TRX_REGION()   { uint8_t irq_mask = PORTC.INTCTRL; PORTC.INTCTRL &= ~PORT_INT0LVL_gm
+
+/*
+ *  This macro restores the transceiver interrupt status
+ */
+#define LEAVE_TRX_REGION()   PORTC.INTCTRL = irq_mask; }
+
+//! @}
+
+/**
+ * @}
+ */
+
+/**
+ * \defgroup xmega_rf212b_zigbit_config_group Configuration options
+ * @{
+ */
+
+#if defined(__DOXYGEN__)
+
+/**
+ * \name Initialization
+ * \note Define these symbols in \ref conf_board.h to enable the corresponding
+ * features.
+ */
+//@{
+
+
+/**
+ * \def CONF_BOARD_ENABLE_USARTD0
+ * \brief Initialize IO pins for USART 0 on port D
+ */
+#  if !defined(CONF_BOARD_ENABLE_USARTD0)
+#    define CONF_BOARD_ENABLE_USARTD0
+#  endif
+
+
+//@}
+
+#endif // __DOXYGEN__
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#endif /* _XMEGA_RF212B_ZIGBIT_H_ */